ClearFog A388 Base Quick Start Guide
Revision and Notes
Date
Owner
Revision
Notes
07 Dec 2021
1.0
Initial release
12 Nov 2024
Yazan Shhady
1.1
Revised the block diagram to include the uSIM connection within the M.2 module and updated the M.2 type from Key-M to Key-B.
28 Nov 2024
Yazan Shhady
1.2
Add Clearfog-Base schematics rev 1.4
Introduction
The following quick start guide provides background information about the ClearFog Base product which use the A388 System on module.
The guide will give a technical overview about the product and by the end of it you should be able to boot an operating system and begin testing your application.
For CN9130 SOM Software, please refrer to the following link:CN913x Build
Hardware Setup
Product Specifications
SOM CPU
ARMADA A388
Processor
32-bit Cortex A9
Core Frequency
up to 1.6GHz
Memory & Storage
32bit DDR3 W/ ECC, Up to 2GB at 1600MT/s
M.2**
MicroSD or 8GB eMMC (Optional)***
Connectivity
1 x mPCIE PCIe X1 Gen2.0
1 x USB 3.0 port
2 x Port dedicated Ethernet
1 x SFP 2.5GbE
I/O & Misc.
mikroBUS
Indication LEDs
User Push Buttons
PoE expansion header
RTC Battery
FTDI (Console Only)
OS Support
Linux, OpenWrt/LEDE, Yocto
Power
Wide range 9V-32V
Dimensions
103mm x 75mm (PCBA)
125mm x 80mm x 31mm (enclosed)
Enclosure
Optional Metal Enclosure
Block Diagram
The following figure describes the ClearFog Base Block Diagram.
Visual features overview
Please see below the features overview of the connector side of the ClearFog Base (A388 SoM assembled).
Print side connector overview of the ClearFog Base.
Software Setup
Cable setup and prerequisites
Here is what you will need to power up the board:
Linux or Windows PC
ClearFog Base with SOM
12V Power adapter (ClearFog Base has wide range input of 9V-32V, it is recommended to use 12V power adapter)
Micro USB to USB for console, the ClearFog Base has an onboard FTDI chip.
IP router or IP switch
Recommended Cables
The following is a list of industry-standard cables, sorted by type, with the necessary compliance requirements that have been proven to work well with the ClearFog product family (ClearFog Base / Pro).
These examples are the cables which SolidRun uses for testing, and should provide enough information to source products from your preferred cable vendor.
Ethernet cable: Monoprice 24AWG Cat6A 500MHz STP
USB Cable: SuperSpeed USB 3.0 Type A Male to Female Extension Cable in Black
SFP connector: GigaLite GE-GB-P1RT-E SFP module with Monoprice 24AWG Cat6A 500MHz STP cable
Boot Select
Before powering up the board for the first time it is recommended to select the boot media. In order to configure the boot media, please refer to ClearFog A388 Boot Select .
Booting from an SD card
The switches on the boot source selector must be set as follows:
Switch 1
Switch 2
Switch 3
Switch 4
Switch 5
OFF
OFF
ON
ON
ON
The following shows how to set the switches on the boot source selector:
Once you set the switches, you can apply the following for booting from an SD card.
1. Downloading the Debian image
For more Debian releases, please visit Debian Releases for Armada 38X.
2. Writing the image to the SD card
Use the following commands for writing the image to an SD card:
For more information, please visit Flashing an SD Card .
3. U-Boot installation
4. Writing U-Boot to the SD card
For more information, you can refer to A38X U-Boot .
5. SD card insertion
Please Insert the SD card into your device.
6. Power connection
Connect your power adaptor to the DC jack, and then connect the adaptor to mains supply.
7. Serial Connection
Please insert the micro USB into your device, then you can refer to Serial Connection for installing necessary serial connection software in Linux/Windows.
Once you installed the necessary serial connection software, you should be able to see the following:
In order to be able to log in , please insert “debian” as a username and password as follows:
GPIO pins Control
To control on the GPIO pins, please follow this page ClearFog Base/Pro GPIO Pins Control .
SFP Modules
For some SFP modules that were tested on SolidRun A388 Platforms see SFP Modules: Tested on A388.
SIM Card Slot
It is possible to utilize a Cellular connection by inserting a SIM card into the SIM card slot. Please observe that a GSM Cellular modem needs to be installed utilizing the mini PCIe connection in order to exploit the cellular connection.
Please Note If your ClearFog has dual SIM card slots, an additional cellular modem will need to be installed in the mini PCIe connection in order to utilize the 2nd SIM connection.
List Of Supported OS
Build U-Boot & kernel from sources
U-Boot Build - A38X U-Boot
Kernel Build - A388 Kernel
Documentation
Last updated